ServicesEntry Doors
Entry Door Replacement in Fort Worth
We replace worn entry doors with prehung fiberglass, steel or wood units. We also fix what the old door was hiding: a soft sill, a jamb shimmed out of square, a threshold patched with caulk. You get a door that latches cleanly and seals tight.

A new door is only as good as the opening it goes into
Most entry door trouble isn't in the door slab itself. On older houses the rough opening has usually moved. The foundation shifts, the header sags a little and the jamb drifts out of plumb. Earlier owners tend to answer that with a planed-down door edge, a relocated strike plate or a bead of caulk across a gap. The door keeps working, badly, for years.
We pull the whole unit, frame and all. Then we look at the framing, the subfloor at the threshold and the flashing before the new door goes in. Our team has over 10 years of experience opening up doorways like these, so we plan for rot and out-of-square framing from the start. If you want new sidelights or a transom, we size them with the door so the trim lines up.
What our entry door replacement includes
- A complete prehung unit
- The slab, jamb, hinges, threshold and weatherstripping arrive assembled and squared at the factory. That avoids hanging a new slab in an old frame that has already warped.
- Sill pan and flashing
- Before the threshold goes down, we set a sill pan and lap flashing tape at the bottom of the opening. Water that gets past the threshold drains back out instead of soaking the subfloor. Wet subfloor is the most common cause of the rot we find under old doors.
- Framing and subfloor fixes
- If the wood under the old sill is soft, we show you the damage and cut back to sound material before going further. You see it in person or in photos, and the work is written down before we do it.
- Shimming, anchoring and adjustment
- We shim at the hinges and the strike and run long screws through the jamb into the studs. Then we adjust until the door swings evenly and latches without a shove.
- Hardware, trim and cleanup
- We fit the lockset and deadbolt, install new brick molding or casing and seal the exterior joints. The old door leaves with us.
Signs your entry door needs replacing
Daylight around the edges
Light at a top corner or under the threshold means the weatherstripping has failed or the door has warped away from the stop. In summer that gap lets cooled air out all day.
Sticking that changes with the season
A door that drags in wet weather and rattles in dry weather usually means the frame is moving with the foundation or a wood slab is swelling. Planing the edge only helps until the next season.
Soft wood at the threshold
Press a screwdriver into the sill and the bottoms of the jambs. If it sinks in, water has been getting under the door for a while, and the framing below may be wet too.
A deadbolt that won't throw
When the bolt only slides home after you lean on the door or hoist it by the knob, the strike and bolt have drifted out of line. That is a security problem, not just an annoyance.
Rust, dents or peeling veneer
Rust along the bottom of a steel door or delaminating veneer on a wood one means the skin is failing and moisture is reaching the core.
What sets the price of an entry door
The price covers more than the door. The condition of the opening, the options you pick and the amount of trim to replace all shape the total. We walk through each line of the quote with you, so no surprise charges appear later. If you want to pay over time, $0 Down on the whole project and 0% Financing options are both available.
Door material
Steel is usually the least expensive and stands up well to forced entry. Fiberglass resists dents and swelling. Solid wood costs the most and needs refinishing every so often.
Sidelights, transoms and glass
Adding sidelights widens both the unit and the opening. Decorative or low-E glass costs more than a solid panel.
Condition of the opening
Rotted sills, a drooping header or out-of-square framing mean more labor and lumber. Rot we can't see can't be priced exactly until the old door is out, so we tell you ahead of time what we suspect and how we would handle it.
Size and casing
A non-standard opening can call for a custom door or new framing. Matching older interior casing profiles may also add work.
How we install an entry door
- 1
Measuring and checking the opening
During the free consultation we measure width and height at several spots, check whether the corners are square and the sill is level, and press on the threshold and lower jambs for soft wood. The quote then spells out the door, the install and any framing work we expect.
- 2
Ordering the right size
Doors in older houses are often an odd size by today's standards. We either order to the measured opening or reframe for a standard door when that costs you less, and we explain the tradeoff before you choose.
- 3
Install day
Most single entry doors are replaced in a day. We put down drop cloths, take out the old unit, repair what's beneath it, then set and seal the new door. Your doorway is shut and lockable before we go.
- 4
Final walkthrough
Together we open, close and lock the door and check that the weatherstrip makes contact. We also show you where the hinges and strike can be adjusted.

Entry door questions we hear most
Can a new door go into my existing frame?
Usually we recommend against it. A new slab in a frame that has moved rarely lines up at the hinges, strike and seal. A prehung unit replaces the jamb and threshold as well, and that is what lets the door seal and latch properly. If a slab-only swap really is the better fit for your opening, we will say so.
Is fiberglass or steel better for a Fort Worth home?
Both work well here. Steel costs less and is very rigid, but it can dent and may rust at the bottom once the finish gets scratched. Fiberglass handles heat and humidity without swelling and takes a wood-look stain. We bring samples to the consultation so you can see them side by side.
What does AAMA certification mean for my door?
AAMA is the industry group that publishes installation standards for windows and doors. Our team is AAMA certified, so the sill pan, flashing and anchoring on your door follow those written methods, not shortcuts.
Will my home ever be without a door overnight?
No. Your old door stays put until the new one is delivered and inspected. The opening is closed and lockable by the end of the day.
Do you also handle my other doors and windows?
We do. Patio doors, storm doors and window replacement are part of our work too. If several openings need attention, we can measure them all on one visit.

See what's behind your old door
We'll measure the opening, check the sill and framing, and explain what we find before you decide anything.